L 71060 SLL 71260 SLEN User manual
Spin phase is off.'Rinse Hold' function ison.5.10 Temperature button 10Press button 10 to change the defaulttemperature.- - = cold water5.11
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsОчен тихаяExtra Silent95° - ColdWhite and colouredcotton with normalsoil.m
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsШторыCurtains40° - ColdSet this programmeto wash curtains. Itadds automati
7) Set this programme to decrease the time and the consumption of energy and water.8) Set this programme to have a good washing results and decrease t
temperature without laundry. Thisremoves all possible dirt from thedrum and the tub.9. USING THE APPLIANCE1.Open the water tap.2.Connect the mains plu
The detergent compartment for the washing phase.If you use a liquid detergent, put it immediately before you startthe programme.Liquid additives compa
4.To use liquid detergent, turn theflap down.With the flap in the positionDOWN:– Do not use gelatinous or thickliquid detergents.– Do not put more liq
Before you press button 4 tostart the appliance, you can can-cel or change the set of the delaystart.9.8 Cancel the delay start1.Press button 4 . The
• Do not wash together white and col-oured items.• Some coloured items can discolourwith the first wash. We recommendthat you wash them separately for
Level TypeWater hardness°dH °T.H. mmol/l Clarke4 very hard > 21 > 37 >3.7 >2511. CARE AND CLEANINGWARNING!Disconnect the appliance from th
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
11.6 Detergent dispenserTo clean the dispenser:121.Press the lever.2.Pull the dispenser out.3.Remove the top part of the liquidadditive compartment.4.
To clean the drain pump:1.Open the drain pump door.2.Put a container below the recess ofthe drain pump to collect the waterthat flows out.3.Press the
218.Clean the filter under the water tapand put it back in the pump into thespecial guides.9.Make sure that you tighten correctlythe filter to prevent
45°20°6.Install again the inlet hose. Makesure that the couplings are tight toprevent leakages.7.Open the water tap.11.9 Emergency drainBecause of a m
Problem Possible cause Possible solution The filters in the waterinlet hose is blocked .Clean the filters. Refer to 'Careand cleaning'. Th
Problem Possible cause Possible solution You did not press but-ton 4 .Press button 4 . The delay start is set. To start immediately the pro-gramme,
13. INSTALLATION13.1 Fixing plate kit(4055171146)Available from your authorized dealer.If you install the appliance on a plinth,secure the appliance i
5.Open the door and remove all theitems from the drum.6.Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put
10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out the plastic spacers.12.Put the plastic caps in the holes.You can find th
13.3 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio
• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a
14. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a
ENGLISH 33
34www.aeg.com
ENGLISH 35
www.aeg.com/shop132930231-A-072013
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se
Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 6 kgSpin speed Maximum 1000 rpm
4.1 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit
• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra
D • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start button, th
Comentarios a estos manuales